Custom Concrete Solutions6 min read

Semix Mobile 120S4: Mobile Batching, Stationary Strength

A Mobile Batching Plant That Doesn't Ask for Extra Site Infrastructure

The Semix Mobile 120S4 is a mobile concrete batching plant with an output of 120 m³/h, designed for contractors and producers who need real batching capacity on a site that can move. What sets it apart from many mobile plants is a simple design decision: its aggregate storage silos are arranged inline, so loading them requires only one ramp and no pre-feeding conveyor. If you want to see how that layout is put together, visit the official Semix Mobile 120S4 page for the full specification.

The Patented Inline Silo Design, Explained

Most mobile batching setups inherit a problem from stationary plant thinking: the aggregate bins sit in a line that a loader cannot reach directly, so a pre-feeding conveyor has to bridge the gap. That conveyor means more steel, more motors, more wear points and more site preparation before the first batch. The Semix Mobile 120S4 takes a different route. Its patented inline aggregate bin design places the storage silos so that a single ramp gives the wheel loader access to load them. The inline silo structure eliminates the need for installing a pre-feeding conveyor altogether. Fewer components between the stockpile and the weighing hopper means fewer things to maintain, fewer things to break, and a shorter commissioning sequence when the plant arrives on a new site.

What One Ramp Actually Saves You

On a project with a tight footprint, the ramp is often the item nobody budgets for until it is needed. A single-ramp loading arrangement reduces the earthworks and the site layout planning required before the plant can run. It also simplifies the traffic pattern for the wheel loader, since every bin is served from the same approach rather than from multiple sides. For a contractor moving between jobsites, that is a practical advantage: the plant's site requirements stay modest and repeatable, and the same loading routine works on the next location.

Robustness of Stationary Plants in a Mobile Chassis

Semix Mobile 120S4 — In SEMIX Mobile 120S4 batch plants, only one ramp is needed to load aggregate storage silos thanks to its' patented design. Inline silo structure eliminates the need for installin

Mobility usually comes with a compromise in structural stiffness. Semix approaches the S4 Series differently. The mobile chassis is built from steel construction intended to deliver robustness that comes very close to a stationary plant, while still allowing the plant to be transferred anywhere on the construction site. In practice, that means the Semix Mobile 120S4 is positioned as a plant you relocate when the job demands it, not one you tolerate because it is portable. The chassis is the foundation for everything above it — the aggregate bins, the weighing conveyors, the mixer platform — so its rigidity matters for how the whole plant behaves under continuous batching.

Extra Strong Aggregate Bin Covers

The same structural thinking appears in the aggregate storage hoppers. The bin covers use trapezoidal bending to reach high strength, and extra reinforcement steels are welded into the empty spaces within the trapezoid. Combined with a protective layer of sheet metal, this construction is what the manufacturer credits for the longevity of the storage bins. Aggregate bins take a beating from loading, weather and material impact, so reinforcement in the cover structure is not a cosmetic detail — it is part of keeping the plant serviceable over time.

Aggregate Storage and Discharge: The Numbers

The Semix Mobile 120S4 carries four linear aggregate bins with a total capacity of 60 to 100 m³, each bin holding 15 to 25 m³. Each bin has two discharging gates, giving eight gates in total. The discharge system uses eight pneumatic pistons and eight pneumatic valves from Festo (Germany), plus two WAM-OLI (Italy) vibrators to keep material flowing. That gate count matters on a plant of this output: with two gates per bin, the weighing conveyor can be fed in a controlled way rather than relying on a single wide opening, and the Festo pneumatics give the discharge a repeatable, actuated behaviour rather than a manual one.

Mixer Options: Single Shaft or Twin Shaft

Semix fits the Mobile 120S4 with mixers offering 3.00 m³ of compacted concrete output for the single shaft option, or 3.33 m³ for the twin shaft. Depending on requirements, either a twin shaft or a single shaft mixer can be adapted to the plant. The 3.33 m³ twin shaft unit listed for this model has a dry volume of 5.0 m³, two 55 kW motors, and handles a maximum grain size of 60 to 75 mm. That grain size range is worth noting for producers working with coarse aggregate mixes, since it defines what the mixer will accept without trouble.

Ni-Hard 4 Wear Parts

Semix Mobile 120S4 — In SEMIX Mobile 120S4 batch plants, only one ramp is needed to load aggregate storage silos thanks to its' patented design. Inline silo structure eliminates the need for installin

Mixing blades, stripping blades and internal wearing plates in Semix mixers are cast in Ni-Hard 4, a high-strength cast iron alloy containing 4% nickel with a tensile strength of up to 1,200 MPa. The nickel creates a tough surface that resists abrasion, while the hardening agents increase hardness and resistance to deformation. The alloy also has a very low coefficient of thermal expansion, which suits high-temperature conditions. For a mixer, the practical translation is straightforward: the parts that contact abrasive aggregate and cement are made from a material selected for high-abrasion, high-impact service, which is exactly the environment inside a batching plant mixer.

Weighing, Conveying and Lubrication

The weighing package on the 3.33 m³ twin shaft configuration includes a cement weighing hopper of 1,600 kg with three load-cells, a water weighing capacity of 1,000 kg with two load-cells, and additive weighing of 1–2 × 20 litres with one load-cell. Material moves on a weighing conveyor with EP 125 / 4-coat belting, four load-cells, a 22 kW or 30 kW motor and gearbox, two WAM-OLI vibrators, 10 mm rubber-coated drums, and a V-type scraper with weights. Safety hardware is included as standard on the conveyor: an emergency stop button and a pull-rope switch. A transfer conveyor with EP 125 / 4-coat belting and a 30 kW motor continues the material path.

Maintenance is addressed with an 8-point automatic lubrication system from SKF-LINCOLN (German). The system uses a pump to send oil to the points on the mixer that need it, keeping the mixer running smoothly and helping protect the equipment from wear. Automatic lubrication is one of those features that rarely gets attention in a brochure but shows up directly in uptime, because it removes the dependence on someone remembering to grease every point on schedule.

Who the Semix Mobile 120S4 Suits

This plant fits producers who need 120 m³/h of batching capacity but cannot commit to a fixed installation, and who do not want to build a pre-feeding conveyor into every new site layout. It suits contractors relocating between projects, and operations where the same loading routine needs to work on site after site. If that describes your requirement, the best solution for reducing site preparation is worth examining in detail — start by reviewing the Semix Mobile 120S4 specifications.

What to Check Before You Specify

Two decisions shape the configuration. First, mixer type: single shaft at 3.00 m³ or twin shaft at 3.33 m³ of compacted concrete per batch, each with different implications for cycle time and mix design. Second, aggregate bin capacity within the 60 to 100 m³ range, which you should match to your loader size and the distance to your stockpiles. Both choices are made at specification stage, so it is worth working through them with the manufacturer rather than defaulting. The full component list — from the Festo pneumatics to the WAM-OLI vibrators and the SKF-LINCOLN lubrication system — is laid out on the product page.

The Bottom Line

The Semix Mobile 120S4 makes its case on two points: a patented inline silo layout that removes the pre-feeding conveyor and needs only one ramp, and an S4 Series chassis built for robustness close to a stationary plant. Around those sit the components that determine day-to-day reliability — Ni-Hard 4 wear parts, automatic lubrication, load-cell weighing, and named European pneumatics and vibrators. It is not a plant for every application, but for a producer who needs genuine 120 m³/h output on a site that moves, the design logic is coherent and the specification is specific. To see the complete configuration and request an offer, visit the official site for the Semix Mobile 120S4.

Explore Semix Mobile 120S4 →

Keep reading